Hot 
Version 2.0 of the previous ADDY 4-bearing engine housing, which forms the engine block for a Puch moped / moped with E50 engine.
New with rod mount, milled instead of cast overflow channels and a less deep cast recess for GME systems so that the housing can also be spindled on for large cylinders with a throat diameter of up to 58 mm. In addition, the serial number has been moved so that it can now be found on the right-hand side. This means you can knock the frame number into the top of the flange as required.
The housing was designed and manufactured specifically for the tuning sector, so some components such as the flat flange for mounting a kick starter have been omitted.
The case has the following special features:
- Enlarged sealing surface in the area of the cylinder base
- Slightly outwardly offset housing bolts, leaving more space for a larger cylinder base;for larger overflow ducts
- Pre-prepared milling surface for GME intake systems
- Fit pins for secure positioning during assembly;for secure positioning when assembling the casing halves
- Additional threads for more flexible ignition assembly
- Extra-large cooling fins in the lower area for better temperature dissipation and thus reduced wear on the crankshaft bearings
- Stud mount, 3 pcs. M6 thread at the original spacing
- Approved in all SAM moped racing and moped cross categories
- Perforated cylinder studs: 44 x 44 mm
- Ø cylinder neck: 48.4 mm (can be spindled up to 58.0 mm if no GME is installed)
Installation tips:
- When installing original intake components and an SRE carburettor, an intake gasket at least 2 mm thick must be used so that the float chamber does not stand up on the GME block.
- With the help of the supplied shims, various gearboxes with different positions, such as those of the 3-bearing or MBR gearboxes, can be cleanly spaced out. Before reassembly, be sure to check that the gear wheel is properly centered!
- The following screw lengths should be used: 7 pcs. M6 x 35 mm / 6 pcs. M6 x 50 mm
Alternative to the original Puch spare part number: 349.3.10.332.0
Quality product of the brand ADDY by Schöb Engineering.
Details
| Manufacturer | ADDY |
| Material | Aluminum |
| Alternative version of the Puch spare part no. | 349.3.10.332.0 |
Suitable for the following models
| Puch | E50 |
Accessories & related products
GPO gasket set | Puch E50
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Hole spacing inlet: 32 - 38 mm · Hole spacing outlet: 42 mm · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Area of application: Standard
11,20 EUR
swiing® revival crankshaft standard (version 2.0) | Puch E50
Manufacturer: swiing® revival parts · Weight: 873 g · Material: Steel · Cheek type: standard · Area of application: Standard · Crankshaft stroke: 43 mm · Thread type: MF10x1 (fine pitch thread) · Thread type: MF8x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
101,30 EUR
swiing® ingenious crankshaft High End with mounted bearings (Version 2.0) | Puch E50
Manufacturer: swiing® ingenious parts · Weight: 968 g · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Area of application: High End · Area of application: Racing · Area of application: Tuning · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
201,60 EUR
Not in stock
Moped fans like you also bought:
Motorex Automatic Motor Oil (ATF) 450 ml
Manufacturer: Motorex · Contents [ml]: 450 ml · Gearbox type: Automatic machine · Temperature resistance (min.): -45 - 200 °C · Area of application: Gearbox lubrication with clutch · Pony spare part no.: A2080 · Sachs spare part no.: 0263 014 002
11,20 EUR
24,89 EUR/l
swiing® revival stud bolt set M6 x 106 mm | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Diameter: 5.9 mm · Thread type: M6x1 (standard thread) · Drive: External hexagon · Width across flats SW: 10 mm · Total length: 106 mm · Thread length: 13 mm · Thread length: 18.5 mm · Alternative version of the Puch spare part no.: 360.1.10.034.1
8,35 EUR
PVL ignition coil analog 105458 / 458115
Manufacturer: PVL · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning · Color: black · Place of use: External (outside the ignition) · Mounting type: Screws · Ø mounting hole: 6 mm · Number of fixing points: 2 pcs
112,40 EUR
PVL stator "1443" ignition
Manufacturer: PVL · Area of application: High End · Area of application: MX · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Material: Aluminum · Surface: dull · Color: black · Color: gray · Number of cables: 2 pcs · Number of fixing points: 3 pcs
112,40 EUR
swiing® revival gasket gearbox cover engine 1 mm | Puch E50
Ø inside: 106 mm · Manufacturer: swiing® revival parts · Thickness: 1 mm · Material: Sealing paper · Color: sand-colored · Number of components: 1 pcs · Ø outside: 116 mm · Number of fixing points: 4 pcs · Alternative version of the Puch spare part no.: 349.1.10.349.1
4,40 EUR
swiing® ingenious crankshaft High End with mounted bearings (Version 2.0) | Puch E50
Manufacturer: swiing® ingenious parts · Weight: 968 g · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Area of application: High End · Area of application: Racing · Area of application: Tuning · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
201,60 EUR
Not in stock
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Manufacturer: Elring · Area of application: Chemistry · Contents [ml]: 70 ml · Color: red · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Temperature resistance (min.): -60 - 300 °C · Gap dimension (max.): 2 mm
25,80 EUR
368,57 EUR/l
Collection only possible with online purchase and appointment.
