Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Tomos Classic, Sprint and FunSport moped / moped.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- Optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set piston to TDC, marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel; this achieves a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good earth (grounding), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal connector:
- 1 = black
- 2 = blue
- 3 = white
Attention: The ignition components stator, rotor, CDI and ignition coil are not compatible with parts of the HPI ignition!
Note: With the Tomos Quadro model, it is possible to fit the ignition, but the E-Start cannot be used.
When purchasing this complete set, you will receive a substantial percentage off the retail price of the individual parts.
Exclusive product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® ingenious parts |
| Ø Internal flywheel | 63.5 mm |
| Tension | 12 V |
| Light coil voltage | 12 V |
| Area of application | Tuning, High End, Racing |
| Performance | 60 W |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Ø Flywheel outside | 75 mm |
| Mounting type | Screws |
| Number of fixing points | 3 pcs |
Suitable for the following models
| Tomos | Classic Sprint FunSport |
Accessories & related products
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Beta 521
Width across flats (trigger): 27 mm · Width across flats Screw: 19 mm · Manufacturer: GPO · Clamping depth: 10 mm · Total length: 55 mm · Total length: 75 mm · Number of components: 1 pcs · Material: Steel · Surface: blackened · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Area of application: (Dis)assembly tool · Strength class: 8.8
11,60 EUR
Hot 
Leonelli 12V voltage regulator (1A quality)
Total length: 50 mm · Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: galvanized (blue) · Tension: 12 V · Performance: 100 W · Type of current: Alternating current (AC) · Mounting type: Screws · Ø mounting hole: 6 mm · Width: 27 mm · Height: 15 mm
40,90 EUR
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Area of application: Chemistry · Color: blue · Contents [ml]: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
25,70 EUR
2 570,00 EUR/l
swiing® ingenious 280 g additional weight HPI Inox
Manufacturer: swiing® ingenious parts · Material: Chrome steel (stainless steel) · Surface: blank · Weight: 300 g · Ø inside: 39 mm · Ø outside: 95 mm · Ø bolt circle: 50 mm · Ø bolt circle: 55 mm · Thickness: 12.5 mm · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Number of fixing points: 7 pcs · Ø mounting hole: 5.5 mm · Ø mounting hole: 10 mm
58,50 EUR
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Spark plug socket: M4 · Cable available: No · Resistance: 1000 Ω · Suppressed: Yes · Ø cable: 5 mm · Ø cable: 7 mm · Color: silver · Pony OEM number: A2099 · Sachs OEM number: 0265 100 00
10,30 EUR
GPO fork lock | Puch
Material: Brass · Material: Spring steel · Material: Steel · Surface: blank · Total length: 40.8 mm · Width: 17 mm · Ø outside: 12 mm · Ø rotating part: 12 mm · Ø Pin: 8 mm · Manufacturer: GPO · Wide locking block: 4.1 mm · Length of turned part: 25.6 mm · Locking block length: 15.3 mm
11,60 EUR
Dell'Orto 19 mm PHBG CS carburetor hand choke
Manufacturer: Dell'Orto · Camouflaged: No · Material: Aluminum · Color: black · Carburetor type: PHBG CS · Nominal diameter: 19 mm · Ø Internal connection: 24 mm · Ø without reducing sleeve: 26 mm · Ø Inside entrance: 19 mm · Ø Output inside: 19 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Choke nozzle size: 60 · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 75 · Size of secondary nozzle: 45 · Mounting type: Plug connection clamped · Total length: 82 mm · Width: 70 mm · Height: 124 mm · Area of application: Racing · Area of application: Tuning
140,60 EUR
GPO 17" spoke set incl. nipple (2.9 x 188 mm) galvanized steel
Manufacturer: GPO · Quantity: 36 pcs · Material: Steel · Surface: galvanized (blue) · Surface: galvanized (yellow) · Length from hook: 188 mm · Ø spoke: 2.9 mm · Ø spoke head: 5.7 mm · Nominal diameter (thread): 3.2 mm · Thread length: 11 mm · Nipple length: 14.7 mm · Ø nipple head: 8 mm · Ø Nipple neck: 5 mm · Hook length: 10.5 mm · Hook angle: 92 °
34,00 EUR
Collection only possible with online purchase and appointment.
