Reinforced pull pin suitable for the manually shifted Z50 engine of Puch X30 Sport mopeds / mopeds, which have a special clutch with 3 plates.
This is often the case with kickstarter engines.
Revised design: The specially developed angular contact ball bearing with a contact angle of 60° (shown in Figure 3) guarantees durability even under the highest loads. The reinforced clutch springs at the bottom of the accessory can only be used in conjunction with the swivel pull pin.
Adjusting the clutch: Figure 4 shows the position of the clutch release lever in relation to the abutment and the ball collar nut in relation to the clutch release shaft. This setting results in maximum disengagement with minimum effort. Particular attention must be paid to the play between the decoupling shaft and the conical collar nut, as the clutch bearing will inevitably break within a very short time if the play is too small. With the clutch cable engaged, the free travel on the clutch release lever should be approx. 3 mm.
The angle "A" on the picture is 58°. On the hand lever, these clearances result in a free travel of approx. 1 cm.
Nostalgic product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® revival parts |
| Material | Aluminum, Steel |
| Area of application | High End |
| Surface | anodized, blackened |
| Color | red, black |
| Ø outside | 44.7 mm |
| Total length | 34.9 mm |
Suitable for the following models
| Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-Gang MS, MV, MV50 3-Gang VSD, DS, VZ, MC |
Accessories & related products
swiing® revival clutch spring 2-disc version (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4 mm · Manufacturer: swiing® revival parts · Area of application: Original · Material: Spring steel · Area of application: Standard · Surface: raw · Color: gray · Number of components: 1 pcs · Ø inside: 30.5 mm · Ø outside: 39 mm · Total length: 19.5 mm
20,20 EUR
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Manufacturer: swiing® ingenious parts · Material: Spring steel · Area of application: Tuning · Color: blue · Surface: coated · Ø wire: 4.6 mm · Ø inside: 30 mm · Ø outside: 39 mm · Total length: 20.5 mm · Number of components: 1 pcs
26,80 EUR
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Manufacturer: swiing® ingenious parts · Material: Spring steel · Area of application: Tuning · Surface: coated · Color: red · Ø wire: 4.5 mm · Total length: 23.5 mm · Ø inside: 30 mm · Ø outside: 39 mm · Number of components: 1 pcs
26,80 EUR
Moped fans like you also bought:
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Viscosity (SAE): 80W · Area of application: Gearbox lubrication with clutch · Oil type: GL4 · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Temperature resistance (min.): -30 - 220 °C
11,20 EUR
24,89 EUR/l
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Manufacturer: swiing® ingenious parts · Material: Spring steel · Area of application: Tuning · Surface: coated · Color: red · Ø wire: 4.5 mm · Total length: 23.5 mm · Ø inside: 30 mm · Ø outside: 39 mm · Number of components: 1 pcs
26,80 EUR
Collection only possible with online purchase and appointment.
