Wheel axle set with closed groove ball bearings for front wire spoke wheels on your Puch moped / moped.
The set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The innovation set works with spoke hubs (spoke rims).
The cable ties show you where to mount what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable ties: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to ensure that the long spacer between the two ball bearings is mounted without play to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
Details
| Ø inside | 12 mm |
| Width | 35.7 mm, 6.6 mm, 11 mm, 2.7 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel |
| Surface | galvanized (blue) |
| Ø shaft | 11.95 mm |
| Total length | 165 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Ø outside | 29.02 mm |
| Height | 9.9 mm, 5.9 mm |
| Thread length | 40.5 mm, 50 mm |
| Width across flats SW | 19 mm |
| Shank length | 74.5 mm |
| Ball bearing closed | Yes |
Suitable for the following models
| Puch |
Accessories & related products
Nut M12x1 x 10 SW19 Wheel nut galvanized
Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut · Drive: External hexagon · Thread type: MF26x1 (fine pitch thread) · Width across flats SW: 19 mm · Height: 10 mm · Thread depth: 10 mm · Strength class: 8 · Area of application: Standard
2,30 EUR
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Ø outside: 29 mm · Diameter: 29 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Width across flats SW: 19 mm · Shank length: 100 mm · Ball bearing closed: Yes
44,90 EUR
Not in stock
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Inner ring width: 9 mm · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: "-" Sheet steel cage ball-guided · Material: Plastic · Material: Steel · Surface: blank · Ø inside: 12 mm · Ø outside: 29.02 mm · Width: 9 mm · Ball bearing closed: Yes
10,30 EUR
swiing® revival wheel nut M12x1 x 4 SW17 galvanized
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Drive: External hexagon · Nut type: Hexagon nut · Thread type: MF12x1 (fine pitch thread) · Height: 4 mm · Width across flats SW: 17 mm · Strength class: 8
3,35 EUR
66HEROES pointed nut "Spike" M12 Inox
Manufacturer: 66HEROES · Material: Chrome steel (known as Nirosta®) · Drive: External hexagon · Thread type: M10x1.5 (standard thread) · Thread type: M12x1.75 (standard thread) · Thread type: M5x0.8 (standard thread) · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread) · Nut type: Pointed nut
7,95 EUR
swiing® ingenious wheel axle with bearing conversion kit cast hub front Ø 29 mm | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Ø outside: 29.02 mm · Width: 34.5 mm · Height: 5.9 mm · Height: 9.9 mm · Total length: 165 mm · Thread length: 40.5 mm · Thread length: 50 mm · Ø shaft: 11.95 mm · Width across flats SW: 19 mm · Shank length: 74.5 mm · Ball bearing closed: Yes
44,90 EUR
Moped fans like you also bought:
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Tire height [%]: 100 · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Valve type: TR4 Auto valve · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 "
11,40 EUR
swiing® revival wheel axle set M12x1 x 185 cast rear wheel galvanized | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.9 mm · Ø outside: 11.8 mm · Total length: 185 mm · Thread length: 26 mm · Thread length: 52.5 mm · Shank length: 100 mm · Width across flats SW: 19 mm
17,20 EUR
Not in stock
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Nipple length: 14 mm · Manufacturer: GPO · Material: Chrome steel (known as Nirosta®) · Surface: raw · Quantity: 36 pcs · Color: silver · Length from hook: 188 mm · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Thread length: 11 mm · Nominal diameter (thread): 3.15 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 °
63,40 EUR
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Ø outside: 29 mm · Diameter: 29 mm · Total length: 190 mm · Thread length: 29 mm · Thread length: 53 mm · Ø shaft: 19 mm · Width across flats SW: 19 mm · Shank length: 100 mm · Ball bearing closed: Yes
44,90 EUR
Not in stock
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Material: Steel · Quantity: 4 pcs · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Total length: 1600 mm · Total length: 2200 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears
11,40 EUR
Collection only possible with online purchase and appointment.
