High-quality full cheek crankshaft for Morini M0, M01 and M1 engines which is installed on Alpa Turbo / Chopper and Malaguti Fifty mopeds, among others.
The connecting rod is highly polished. In addition, the rear connecting rod bearing is a silver bearing, which has excellent emergency running properties. The balancing bores of the racing crankshaft are sealed with aluminum inserts for greater pre-compression.
Note: The crankshaft does not fit FMT1 CH engines.
Corresponding bearings, oil seals, racing cylinders etc. can be found in the accessories section.
Branded product from the Portuguese manufacturer Jasil under the Top Racing brand.
Details
| Manufacturer | Jasil |
| Cheek type | Full cheeks |
| Area of application | Racing |
| Crankshaft stroke | 39 mm |
| Total length of crankpin on clutch side | 71 mm |
| Total length crankpin ignition side | 67.25 mm |
| Ø piston pin (B) | 12 mm |
| Ø Bearing seat (clutch side) | 17 mm |
| Ø Bearing seat (ignition side) | 17 mm |
Suitable for the following models
| Alpa Chopper / Turbo | |
| Malaguti |
Accessories & related products
Airsal 43.5 mm cylinder kit 12 mm KoBo | Morini
Manufacturer: Airsal · Area of application: Tuning · Material: Aluminum · Surface: sandblasted · Ø cylinder neck: 47.9 mm · Camouflaged: No · Nominal diameter: 43.5 mm · Number of fixing points: 4 pcs · Ø outlet inside: 23.2 mm · Ø piston pin (B): 12 mm · Hole pattern [mm]: 46 x 46 · Decompressor: No · Hole spacing outlet: 35 mm · Outlet type: straight · Thread outlet: M5x0.8 (standard thread)
112,60 EUR
Moped fans like you also bought:
Magura cable clamp Ø 8 x 15 mm
Ø Bundle: 6 mm · Ø Cable bushing: 2.3 mm · Manufacturer: Magura · Material: Brass · Material: Steel · Surface: blue galvanized · Surface: nickel-plated · Thread type: M6x1 (standard thread) · Ø outside: 8 mm · Drive: External hexagon · Drive: Slot · Screw head: Hexagon · Area of application: Standard · Width across flats SW: 7 mm · Thread length: 7 mm · Total length: 15 mm
2,80 EUR
swiing® revival snap ring low control bearing set (version 2.0)
Manufacturer: swiing® revival parts · Material: Spring steel · Surface: blank · Thickness: 0.6 mm · Nominal diameter: 20 mm · Nominal diameter: 28 mm · Height: 7 mm · Sachs spare part no.: P0521 · Puch spare part no.: 349.1.30.015.1
2,80 EUR
Magura adjusting screw brake long
Ø External head: 9.1 mm · Manufacturer: Magura · Material: Brass · Surface: nickel-plated · Color: silver · Thread type: MF6x0.75 (fine pitch thread) · Total length: 47 mm · Total length: 65 mm · Drive: Knurled screw · Thread length: 24 mm · Ø shaft: 6 mm · Shank length: 11 mm
4,40 EUR
NTN 6203 C3 Ball bearing 17/40/12
Bearing type: Deep groove ball bearing · Bearing cage: "-" Sheet steel cage ball-guided · Width: 12 mm · Stock number: 6203 · Inner ring width: 12 mm · Manufacturer: NTN · Ø inside: 17 mm · Bearing clearance: C3 · Groove ring: No · Material: Steel · Surface: blank · Ø outside: 40 mm · Area of application: Standard · Ball bearing closed: No
10,00 EUR
Oil level screw engine | Zündapp Bergsteiger / Alpa Chopper / Malaguti Fifty
Manufacturer: ALPA · Area of application: Standard · Material: Steel · Color: silver · Surface: blue galvanized · Drive: Slot · Thread length: 16 mm · Screw head: Cylinder head · Number of components: 1 pcs · Thread type: M6x1 (standard thread)
2,70 EUR
Collection only possible with online purchase and appointment.
