Blue galvanized gear holder to loosen the nut on the countershaft.
Fits hand-shifted Puch Z50 engines of Puch X30 Velux mopeds / mopeds.
Good, inexpensive standard spare part. GPO – GOOD PARTS ONLY.
Original Puch spare part number: 360.1.70.014.1
Details
Manufacturer | GPO |
Area of application | (Dis)assembly tool |
Suitable for the following models
Puch | Z50 (X30 Velux) |
Accessories & related products
Motorex Brake Cleaner 750 ml
Manufacturer: Motorex · Area of application: Chemistry · Area of application: Cleaner · Contents [ml]: 750 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Extremely flammable aerosol · Hazard warning: May be fatal if swallowed and enters the respiratory tract · Hazard warning: May cause drowsiness and dizziness · Hazard warning: Pressurized container: may burst when heated · Hazard warning: Toxic to aquatic organisms (with long-term effects) · Signal word: Danger · Hazard pictogram: GHS02 - Highly flammable · Hazard pictogram: GHS04 - Gas under pressure · Hazard pictogram: GHS07 - Caution dangerous
28,10 EUR
37,47 EUR/l
Moped fans like you also bought:
GPO piston 41 mm (12 mm KoBo) | Puch X30 Velux fan-cooled
Nominal diameter: 41 mm · Manufacturer: GPO · Ø outside piston (A): 40.94 mm · Ø piston pin (B): 12 mm · Compression height (C): 23.2 mm · Curvature (D): 3.7 mm · Total piston height (E): 49.3 mm · Number of piston rings (F): 2 pcs · Piston ring mold: L-ring · Piston ring mold: Rectangular ring · Piston ring impact: Flank safety device (FS) · Piston ring impact: Internal fuse (IS)
56,20 EUR
Clutch cable / brake cable Ø 1.5 mm x 225 cm (pear-shaped nipple)
Ø Stranded wire: 1.5 mm · Nipple shape: Pears · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: blue galvanized · Number of components: 1 pcs · Cable length: 2250 mm · Piaggio spare part no.: 270460
2,70 EUR
swiing® revival special nut M6 SW8 (sprocket ref. back pedal / intake manifold)
Height: 6 mm · Width across flats SW: 8 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Nut type: Hexagon nut · Thread type: M6x1 (standard thread) · Drive: External hexagon
3,25 EUR
swiing crankshaft | High End Puch X30 Velux (Z50)
Manufacturer: swiing · Weight: 954 g · Thread length: 8 mm · Thread length: 13 mm · Material: Aluminum · Cheek type: Full cheeks · Material: Steel · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Connecting rod length center-center: 90 mm · Number of gears: 2 pcs · Total length of crankpin on clutch side: 58 mm · Total length crankpin ignition side: 67 mm · Ø crank webs: 70 mm · Area of application: High End · Area of application: Racing · Area of application: Tuning · Thread type: MF10x1 (fine pitch thread) · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Length 1st paragraph: 20.3 mm · Length 2nd paragraph: 19 mm · Ø 1st step (on the coupling side): 17 mm · Ø 2nd shoulder (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm
180,20 EUR
Not in stock