Foot shift pawl | Sachs 50/3, 50/4

Slotted nut M6 shift rod | Sachs 50/3, 50/4 foot control

Material: Steel · Surface: burnished · Nut type: Slotted nut · Drive: Slot · Thread type: M6x1 (standard thread)

Shift rod in gearbox | Sachs 50/4

Material: Steel · Surface: raw · Total length: 118.5 mm · Thread type: M5x0.8 (standard thread) · Thread type: M6x1 (standard thread)

Shift unit 3-speed foot shift | Sachs 50/3

Shift unit 4-speed foot shift | Sachs

Shaft seal NBR 10/16/4.5 A Shift shaft | Sachs 50/3, 50/4

Temperature resistance (min.): -30 - 100 °C · Simmering type: A - With rubberized outer part / one sealing lip. · Manufacturer: Sachs · Material: NBR · Place of use: Shift shaft · Surface: rubberized · Width: 4.5 mm · Ø outside: 16 mm · Ø inside: 10 mm

Locknut M6 shift rod foot shift NOS | Sachs 50/3, 50/4

Manufacturer: Sachs · Nut type: Slotted nut · Drive: External hexagon · Thread type: M6x1 (standard thread)

Foot control mounting plate | Sachs 50/3, 50/4

Material: Steel · Surface: chrome-plated

Pawl spring foot control Sachs 50/3 & 50/4

Spring design: Special spring

Shift shaft foot control | Sachs 50/3, 50/4

Material: Steel · Surface: Hardened

Locking spring foot control Sachs 50/3 & 50/4

Spring design: Special spring

swiing® revival membrane seal 0.4 mm | Sachs 50/2, 50/3, 50/4 (A1840)

Manufacturer: swiing® revival parts · Material: Oiled paper · Thickness: 0.4 mm · Hole spacing inlet: 67 mm · Pony OEM number: A1840 · Sachs OEM no.: 0250 106 00

GPO Adjusting nozzle Bing SSB | Sachs

Manufacturer: GPO · Component group Carburetor: Spraying · Material: Brass · Surface: blank · Quantity: 1 pcs · Carburetor type: SSB · Nozzle type: Main nozzle · Nozzle thread: MF7x0.75 (fine pitch thread) · Total length: 65.7 mm · Drive: External hexagon · Width across flats SW: 11 mm

ESJOT pinion 14 | Sachs (50/3, 50/4)

Manufacturer: ESJOT · Material: Steel · Surface: raw · Chain type: 415H · Recording type: Ø15 x SW12 · Chain pitch: 1/2" x 3/16" · Number of teeth: 14 pcs · Cranking (offset): 10.5 mm

swiing® revival ball bearing countershaft | Sachs 50/2, 50/3, 50/4, 503 2AL/2BL (A2531)

Bearing type: Deep groove ball bearing · Stock number: E15 · Inner ring width: 25.6 mm · Manufacturer: swiing® revival parts · Bearing clearance: CN (standard) · Bearing cage: "-" Sheet steel cage ball-guided · Material: Steel · Width: 8 mm · Ø outside: 35 mm · Ø inside: 15 mm · Area of application: High End · Area of application: Standard · Thread type: MF20.8x1 LH (fine/left-hand thread) · Pony OEM number: A2531 · Sachs OEM no.: 0286 079 105

Shift pin foot control | Sachs 50/4

Material: Steel · Surface: Hardened

Transmission lever foot shift | Sachs 50/4

Material: Steel · Surface: raw